1、Machinability of Hydrogenating Titanium Alloy TC4
2、Electron Beam Welding of Dissimilar Materials between QCr0.8 and TC4;
3、High-temperature Deformation Process and Microstructural Characteristics of TC4 Alloy
4、Localized Adiabatic Shear Deformation of TC4 and DT4 Alloys
5、Study on Superplastic Forming and Precision Control of TC4 Alloy Deep Cups;
6、The stress relaxation behavior characters of TC4 alloy and influence of processing factors were studied.
7、Study on Microstructure and Mechanical Properties of C/C Composite and TC4 Brazed Joint;
8、Study on TC4 Powder Laser Micro Cladding Deposition Manufacturing by Powder Precise Jet
9、Based on the direct-reverse superplastic forming TC4 deep cylinder with uniform thickness thickness accuracy: 1.
10、The effect of the atmosphere on the structure and properties of ion nitriding layer of alloy TC4 was investigated.
11、Microstructure refinement surface layer was obtained in TC4 Titanium Alloy surface treated by a high-energy shot peering (HESP) technique.
12、In order to solve the problems occurring in the combined bending and forming process of TC4 sheet 3.
13、However, results from AIM and TC4 may modify this view—which is the main point of deploying them.
14、The influence of two abnormal forging processes on the microstructures and tensile properties of TC4 alloy is investigated.
15、Based on the experiments of high-speed milling titanium alloy TC4 the effects of cutting parameters, the materials of the milling cutters on cutter we ar are discussed.
16、The diffusion zone width of main alloying elements increases and hardness of the friction weld zone near TC4 titanium alloy side improves after post-weld heat treatment.
17、The combustion resistance properties of TC4 and TC11 titanium alloys had been studied by means of titanium combustion testing equipment and metallographic examination.
18、Methods: Electrochemical technique was adopted to detect the changes of anode polarization curves of TA2 and TC4 after welding with laser or pulsed tungsten argon arc.
19、结果表明：在相同温度下，混合陶瓷粉对TC4合金基体的浸润*优越于A-W生物活*陶瓷粉；
20、Coated by the mixed powders of neutro-glass and A-W bioactive glass ceramics on TC4 matrix and presintered to form a transition layer, the samples then were coated with A-W powders and sintered again.
21、The results show that the wettability of the mixed ceramic powders on TC4 alloy matrix is better than that of the A-W powders on it at the same temperature.
22、结果表明：储能焊能够实现TC4钛合金薄板的快速凝固焊接，焊接接头由熔核和熔核向母材过渡的熔合区（线）组成。
23、利用钛合金阻燃*能测试装置，结合金相分析，研究了TC4和TC11两种合金的抗燃烧*能，分析了钛合金燃烧产物的显微组织特点。
24、除了AIM与TC4工程，美国国家航天宇宙管理局同时也发*了一系列叫做“A-列车”的气候感应卫星，用以提供针对云层的纵剖图的全球范围的研究分析。
25、采用电磁涡流激振的振动疲劳试验，对TC4材料制成的平板叶片受外物损伤后的剩余振动疲劳寿命进行了研究。
26、方法：采用动电位极化技术，分别测定激光焊接及脉冲氩弧焊接TA2和TC4后，材料阳极极化曲线的变化。
27、TC4工程将研究出关于含*卷云的各种资料，这种云层是在大气上层中通过受热量驱使或对流的暴风雨变化过程中形成的，而此暴风雨也是与热带暖水海洋上空的状况密切相关。
